低价现货LCP 6130L美国杜邦江苏苏州山东宁波
更多该厂家低价现货LCP 6130L美国杜邦江苏苏州山东宁波类似产品
LCP 6130L 美国杜邦公司 物性数据
①原料描述部分 暂无此原料描述部分┄
②原料技术数据 性能项目 试验条件[状态] 测试方法 测试数据 数据单位
基本性能 密度 --- ISO 1183 1620 Kg/m3
机械性能 断裂应力 1.0mm,23℃(73ºF) ISO 527-1,2 180 MPa
断裂应力 2.0mm,23℃(73ºF) ISO 527-1,2 150 MPa
断裂应力 4.0mm,23℃(73ºF) ISO 527-1,2 130 MPa
断裂应变 1.0mm,23℃(73ºF) ISO 527-1,2 1.9 %
断裂应变 2.0mm,23℃(73ºF) ISO 527-1,2 2.2 %
断裂应变 4.0mm,23℃(73ºF) ISO 527-1,2 1.8 %
拉伸模量 1.0mm,23℃(73ºF) ISO 527-1,2 16700 MPa
拉伸模量 2.0mm,23℃(73ºF) ISO 527-1,2 15300 MPa
拉伸模量 4.0mm,23℃(73ºF) ISO 527-1,2 13000 MPa
弯曲模量 1.0mm,23℃(73ºF) ISO 178 16200 MPa
弯曲模量 2.0mm,23℃(73ºF) ISO 178 12500 MPa
弯曲模量 4.0mm,23℃(73ºF) ISO 178 12000 MPa
弯曲强度 1.0mm,23℃(73ºF) ISO 178 211 MPa
弯曲强度 2.0mm,23℃(73ºF) ISO 178 191 MPa
弯曲强度 4.0mm,23℃(73ºF) ISO 178 167 MPa
IZOD冲击强度 3.2mm(0.126in) ASTM D-256 120 J/m
Charpy缺口冲击强度 23℃(73ºF) ISO 179-LeA 35 KJ/m2
Charpy无缺口冲击强度 23℃(73ºF) ISO 179-LeU 35 KJ/m2
挠曲温度 1.80MPa ISO 75-1,2 265 ℃
介电强度 23℃(73�H) ASTM D-149 40 Kv/mm
电气性能 体积电阻率 --- IEC 60093 >1×1014 Ohm-cm
表面电阻率 --- IEC 60093 >1×1015 Ohm
介质常数 1×102Hz IEC 60250 4.5 Ohm
介电强度 23℃(73�H) ASTM D-149 35 Kv/mm
介电强度 23℃(73�H) ASTM D-149 29 Kv/mm
介电强度 0.8mm(0.032in) ASTM D-149 30 Kv/mm
介电强度 1.6mm(0.063in) ASTM D-149 29 Kv/mm
介电强度 3.2mm(0.126in) ASTM D-149 26 Kv/mm
介电常数 0.8mm(0.032in),23℃(73�H) ASTM D-150 4 ---
介电常数 3.2mm(0.125in),23℃(73�H) ASTM D-150 4.4 ---
介电常数 0.8mm(0.032in),23℃(73�H) ASTM D-150 3.6 ---
损耗因数 3.2mm(0.125in),23℃(73�H) ASTM D-150 0.027 ---
损耗因数 0.8mm(0.032in),23℃(73�H) ASTM D-2520 B 0.004 ---
损耗因数 1.6mm(0.063in),23℃(73�H) ASTM D-2520 B 0.004 ---
损耗因数 3.2mm(0.125in),23℃(73�H) ASTM D-2520 B 0.004 ---
介电常数 3.2mm(0.125in),23℃(73�H) ASTM D-150 3.9 ---
介电常数 0.8mm(0.032in),23℃(73�H) ASTM D-2520 B 4.4 ---
介电常数 1.6mm(0.063in),23℃(73�H) ASTM D-2520 B 4.3 ---
介电常数 3.2mm(0.125in),23℃(73�H) ASTM D-2520 B 4.3 ---
损耗因数 1×102Hz IEC 60250 150 ---
损耗因数 0.8mm(0.032in),23℃(73�H) ASTM D-150 0.013 ---
损耗因数 3.2mm(0.125in),23℃(73�H) ASTM D-150 0.013 ---
损耗因数 0.8mm(0.032in),23℃(73�H) ASTM D-150 0.026 ---
热 性 能 解链温度范围 --- --- 350-360 ℃
模压温度范围 --- --- 90 ℃
干燥温度 --- --- 130 ℃
熔体温度 --- ISO 3146-C 335 ℃
其它性能 工业含水量 --- --- <0.01 %
LCP塑胶原料(液晶聚合物)
美国杜邦6130、6130L,7130L,1110,美国杜邦1000.16130,5244L,1723,
美国杜邦17235,3226L,5130L,5145L **,
美国杜邦5244L,6130 **,6130L-WT010,
美国杜邦 6330 NC010,6330-WT010,7244-N0100
美国杜邦77110L,95140-**010,LGM641-0001L,
美国杜邦55201,6330-**010,7130L **010,
美国杜邦77110L-**010,7755-**010,B230 **4302,
美国杜邦ZE16130A-WT010,ZE16202 **010,ZE16202 **010,
日本宝理A130,A410,A422,B130,C130,C810 VF2001,E130
日本宝理C130M,E130i,E130i VF2201,E130I-210P,E130i-NC,
日本宝理E140i,E471i,E480I **210P,LX70G35B BH,S135,
日本宝理SG02C **225,SG52C,E130i-**210P,E463I-**210P,
日本宝理T130,E130G **210P,E130G VF2201,E130i-**205P,
日本宝理E130M VF2201,K130 VF3001,S135 **,S471,E130i-**211
美国泰科纳C130,L130,9500-YW,A130D-3**-VD3006,A540-NC-VF3001,
美国泰科纳E130D-2-VD3005,B130D-2-VD3005,E130i-NC-VF3001,
美国泰科纳E543-BLU,S471-**010P,S135-**010P,E130i-VC3030-GY,
日本百富,**E473,**S408,**E471,**E350,**E130
日本东丽TX05M **,L204T40,L304T40 **,L304T40 **,L304M35-B,
日本东丽L304M35,L304G35,L204G35,
日本杜邦1110-**010,7225-**010,3140L-WT010,6130L,6130L-**010,
日本杜邦7225-**010,7225-NC010,9140HT-NC010,5145L-WT010,5415L WT010,
日本住友6808THF-NC,E4008,E4008-**,E5002L NC,E5006L,E5006L-**,E5008,
日本住友E5008L,E6006L,E6006L MR-B,E6007LHF,E6008 NC,E6010,E6807,
日本住友E6807LHF NC,E6807LHF-B-Z,E6808THF-B,E6810(**),E6810GHF-NC,
日本住友E7006,E6007LHF-MR-BZ,E6019F,E6808 UHF BZ,E4008 MR-B,
日本**化学,FC-110,G-430,G-430-**,MG350-A540,NC-301-B,M-450, 日本油墨 H**02,LD-235,LD-235-B,MG350,
**宝理E130i,E130I-210P,E130i-**210P,E471i 210P,E130i VF2201
1、LCP的特性有
a、LCP具有自增强性:具有异常规整的纤维状结构特点,因而不增强的液晶塑料即可达到甚至超过普通工程塑料用百分之几十玻璃纤维增强后的机械强度及其模量的水平。如果用玻璃纤维、碳纤维等增强,更远远超过其他工程塑料。
b、液晶聚合物还具有优良的热稳定性、耐热性及耐化学**品性,对大多数塑料存在的蠕变特点,液晶材料可以忽略不计,而且**、减磨性均**。
c、LCP的耐气候性、耐辐射性良好,具有**的阻燃性,能熄灭火焰而不再继续进行燃烧。其燃烧等级达到UL94V-0级水平。
d、LCP具有优良的电**缘性能。其介电强度比一般工程塑料高,耐电弧性良好。在连续使用温度200-300℃,其电性能不受影响。间断使用温度可达316℃左右。
e、LCP具有**的耐腐蚀性能,LCP制品在浓度为90%酸及浓度为50%碱存在下不会受到侵蚀,对于工业溶剂、燃料油、洗涤剂及热水,接触后不会被溶解,也不会引起应力开裂。
2、LCP的应用
a、电子电气是LCP的主要市场:电子电气的表面装配焊接技术对材料的尺寸稳定性和耐热性有很高的要求(能经受表面装配技术中使用的气相焊接和红外焊接);
b、LCP:印刷电路板、人造卫星电子部件、喷气发动机零件、汽车机械零件、**方面;
c、LCP加入高填充剂或合金(PSF/**/PA):
本公司主要销售原料有:
PET : **南亚系列、美国杜邦系列
** :**南亚系列、基础创新(原美国GE)系列、美国杜邦系列 、
POM(聚**):美国杜邦系列、德国巴斯夫系列、日本旭化成系列、泰科纳/赫斯特系列、
PA(尼龙): **南亚系列、美国杜邦系列、德国巴斯夫系列、
PC(聚**脂):德国拜耳系列 、 日本三菱工程系列、韩国三星系列、
PC/ABS合金料:基础创新(原美国GE)系列、德国拜耳系列 、**奇美系列、
日本帝人系列 、 韩国LG系列
真诚合作.共求发展 **秉承客户至上.品质的宗旨!
面向地区:全国
联系人:易武**
联系手机:15995642148
联系QQ:1533676417
联系邮箱:wrg899**126**
ABS : **奇美系列 韩国LG系列
**长春系列
、日本宝理系列 、三菱工程系列
日本宝理系列、韩国工程塑料、日本三菱工程系列、**台丽钢系列、南通宝泰菱系列
德国朗盛系列
、 日本东丽系列 、日本旭化成系列
基础创新(原GE)系列、日本帝人系列
、 韩国LG-DOW系列
- 联 系 人:易军 先生
- 工作 QQ :948928408
- 电 话: 查看完整电话
- 手 机: 查看完整电话
- 网 址:http://www.wrgsh.com
- 地 址:中国 江苏 苏州 中国