高层建筑**系统系统图及说明
所属行业 | 其他 |
厂家/商户所在地 | 陕西-西安 |
公司名 | 西安鼎兴工程有限公司 |
主营产品 | 三防设备,无线液位,暖通排气阀 |
查看其它工厂 [其他] 类似产品 查看其它工厂 [木工机床部件] 类似产品 查看其它工厂 [施工现场用品] 类似产品 |
更多该厂家高层建筑**系统系统图及说明类似产品
高层建筑**系统系统图说明
图1是本实用新型高楼建筑施工自动供水装置的结构示意图。
图中,1.压力变送器 2.储压罐 3.手动蝶阀 4.止回阀 5.橡胶软接头 6.水泵 7.底阀 8.水位控制仪 9.浮球阀 10.蓄水池 11.变频控制柜 12.截止阀 13.储压罐排污阀 14表阀1 5.水压阻尼器 16.蓄水池底座
附图中,虚线框内为高楼施工供水自动控制装置。
具体实旖方式
下面结合附图和具体实施方式对本实用新型进行详细说明。
本实用新型高楼建筑施工自动供水装置是一种实施例的结构,如图l所示。包括动力部分、控制部分及管阀部分。
动力部分包括储压罐(2)和水泵(6)。
控制部分由变频控制柜(11)、压力变送器(1)及水位控制仪(8)组成。
管阀部分包括连接上述各部分的管道和管道上设置的阀门。
各部分的作用
动力部分:储压罐(2)根据系统压力的消长自动储存压力及释放压力,水泵(6)接受变频控制柜(11)调节与控制,按其指令增压、减压、保压。
控制部分:变频控制柜(11)采集压力变送器(1)的信号及水位控制仪(8)的水位信号,并与预先设定的信号进行比较,得出偏差值,根据偏差值的大小与性质,发出增频、降频、休眠、启泵、停泵指令,对高楼建筑施32的作业面实施恒压供水。
管阀部分:连接或阻断流体系统,使各单元保持相对**,**高楼建筑施工用水沿规定方向流动,方便水系统维护、保养。
本实用新型高楼建筑施工自动供水装置的工作过程:
打开水源阀门(12),使水进入蓄水池(10),蓄水池(10)的水位由自力式浮球阀(9)来控制,低于设定水位时,该阀自动**,水池水位达到设定上**,停止进水。
当水源停止供水,蓄水池(10)水位下降至用水下**,水位控制仪(8)自动切断变频控制柜(11)二次控制回路,水泵停止抽水,使水泵(6)得到低水位保护。
1频操作:接通电源,电源指示灯亮,将转换开关旋至“工频”位置,按下启动按钮,水泵(6)开始转动,运行指示灯亮,同时水压阻尼器(1 5)将瞬间传至压力变送器(i)的正向水锤阻尼,压力变送器(1)压力指示缓慢上升,按下停止按钮,水泵(6)停止运转,同样水压阻尼器(1 5)将瞬间传至压力变送器(1)负向水锤阻尼,系统停止加压。
变频操作:接通电源,电源指示灯亮,将转换开关旋至“变频”位置。当系统用水负荷较大时,系统水压在设定压力以下,变频控制系统发出增频指令,水泵(6)加速转动,运行指示灯亮,压力变送器 (1)指示压力值不断上升;随着用水负荷不断减少,实测压力值比设定压力值大时,变频控制系统发出降频指令,水泵(6)转速减小:系统负荷很小时,维持6分钟,水泵(6)即进入休眠保压状态。
当施工作业面开启龙头数量急剧增加时,压力随即下降至设定值以下,水泵(6)又立即苏醒,增频加压,**建筑施工作业面恒压水的供给。
用水量很小时,水泵(6)可不启动,由储压罐(2)释放压力,给作业面供水。
随着施工楼层的增高,龙头数量加大,系统压力设定值也要随之上升,为了**建筑施工高层供水,在低楼层用水龙头的前端应加装减压阀,或在高层用水时低层用水龙头要尽量减小阀的开度,降低水头损失,**高层施工供水a
当大楼封顶时,水压设定值被调到,水泵(6)全压运行。
- 联 系 人:王女士 女士
- 工作 QQ :754965698
- 电 话: 查看完整电话
- 手 机: 查看完整电话
- 网 址:http://www.dxwk.com
- 地 址:中国 陕西 西安 中国内陆